Filter Parts

This round nylon bristle brush is ideal for cleaning inside most magnetic drive pumps with removable rotor/impeller. The bristles are designed to remove algae buildup ...

This pre-filter foam is approximately 2-1/4" Diameter by 6" Length. The inner diameter measures 1-1/8" and will fit over many aquarium intake tubes for use as a pre-fi...

This pre-filter foam is approximately 2-1/4" Diameter by 7" Length. The inner diameter measures 1-1/4" and will fit over many aquarium intake tubes for use as a pre-fi...

The stainless rotor shaft for the Rena Filstar XP filters rarely needs replacing. The shaft centers the rotor/impeller in the filter motor to achieve an efficient and ...

The shaft bearing/bushing is located in the bottom of the rotor well and in the center of the impeller cover. It is rarely replaced and has nothing to do with the spee...

The SmartHeater unviversal connection kit allows the SmartHeater to be used with other brands of external filters and replaces the intake tube supplied by the manufact...

The canister replacement for the Rena Filstar XP1 external canister filter consists of the outer canister, inner filter basket and rubber feet. To avoid breaking the c...

Replacement tubing for the Rena XP Filters consists of two, 6.5 foot lengths. These are the original tubes that come with the XP4, but will also fit the XP1, XP2 and X...

Bio Chem Star Caddy. Fits all Smart Filters including 740,741,742. Holds up to 16 BioChem Stars. Does not include BioChem Stars

The SmartFilter Cartridge Caddy fits all Rena SmartFilters including model 20, 30 and 55. Additional cartridge holders make swapping standard filters for special filte...

Replacement extension and strainer for Rena Smart Filter. Additional extension can be used to increase the length of the intake for use with deeper tanks.

Additional SmartFilter inlet extensions can be used to increase the intake length for use in deeper tanks.

Replacement outer housing and lid for Rena SmartFilter 20

The rotor/impeller assembly for Rena SmartFilter 20 consists of the magnet and impeller blades. These should be replaced when you notice a significant slowing of filte...

This is the original strainer for the Rena SmartFilter and fits all models including SmartFilter model 20, 30 and 55. Replace if broken or lost to prevent clogging or ...

Replacement outer housing and lid for Rena SmartFilter 30

Complete motor assembly for the SmartFilter 30. This includes the motor caddy, motor and rotor/impeller assembly. This is the fastest and easiest way to replace a moto...

The rotor/impeller assembly for Rena SmartFilter 30 consists of the magnet and impeller blades. These should be replaced when you notice a significant slowing of filte...

Replacement outer housing and lid for Rena SmartFilter 55

Complete motor assembly for the SmartFilter 55. This includes the motor caddy, motor and rotor/impeller assembly. This is the fastest and easiest way to replace a moto...

The rotor/impeller assembly for Rena SmartFilter 55 consists of the magnet and impeller blades. These should be replaced when you notice a significant slowing of filte...

These are original inlet/outlet accessories for the Rena Nexx filter system from API. It includes everything but the flexible tubing. Contents Suction Cups = 11 Clips ...

This is an original replacement motor and mounting bracket for the Rena Nexx Filter. The mounting bracket *does not include suction cups*. Suction cups are included in...

This is the original tubing supplied with the Nexx Filter from API. Includes 2, 5 foot pieces for the inlet/outlet and one short piece for the supplied water pump that...

The Rubber feet on the Rena XP Filstar filters stabilizes the filter base and dampens any sound from filter operation. Over time these feet will loose elasticity and s...

The basket lid seals the bottom of the motor to the top of basket assembly. This insures that water flowing from the aquarium will flow through the baskets from the bo...

The basket separation grid when used, makes two filtration media chambers from one basket. This results in smoother flow of water through the filter, more contact time...

Filstar media baskets have been designed with many convenience features for the user and allow for a high degree of customization. When properly placed in the filter t...

The outlet pipe connects the flexible tubing exiting from the filter to the outlet accessories which terminate with either the spraybar or power jet nozzle. This outle...

The power jet nozzle is used to direct the water discharged from the filter onto the water's surface. This increases agitation and aeration in the tank for better oxyg...

840135-00-Priming-Funnel-9-or-P The priming funnel is used on initial setups to prime the system for startup. It is only needed for the initial setup and when the inle...

840138-00 Suction Cup Clamps (4pk) (L) These brackets attach (clamp) to the inlet/outlet tubes and coupled with the large suction cups will hold the inlet/outlet pipe ...

This is the original shaft for Rena Filstar XP filters produced before 2003 when the system used a ceramic shaft for the rotor. We have a very limited supply of these ...

The item 841542-00 version of the canister replacement for the Rena Filstar XP1 external canister filter consists of the outer canister, rubber feet and clips. To avoi...

The Quick Disconnect (QD) unit contains the integrated inlet/outlet system for the filter. The unit is removed by lifting the handle which releases the connection to t...

The flow control valve for the Rena Filstar XP canister filter regulates the flow from the filter into the aquarium. This is a simple "flapper valve" that when turned ...

Original replacement motor for the Rena Filstar XP1 and includes a canister O ring and impeller cover seal . It does not include the Quick Disconnect Unit or rotor/imp...

The Rena Filstar XP impeller cover caps the area containing the rotor/impeller and fixes one end of the rotor shaft to stabilize the rotor/impeller. The other end of t...

The Rena Filstar XP Canister clip/hinge seals the motor to the top of the canister. This prevents water leaks from the filter. The clips exert positive pressure on the...

The quick-disconnect Orings prevent leaking around the inlet and outlet stems of the Quick-disconnect unit when inserted into the top of the motor and when the filter ...

There are two outlet extensions included with the Rena Filstar XP Canister Filters. The taller outlet extension will extend the discharge outlet (spraybar or power jet...

There are two outlet extensions included with the Rena Filstar XP Canister Filters. The short extension will discharge water from the filter(spraybar or power jet) int...

This is a one-piece spraybar that securely attaches to the discharge tube or flow control valve. The spraybar discharges water into the aquarium more slowly than the p...

The inlet pipe allows the unit to be primed for the initial filter startup and if the filter needs to be re-primed after a major cleaning or teardown. Once primed, wat...

This is the complete inlet/outlet accessory tray that comes with the Rena Filstar XP external canister filter system. This is version 2 and includes the new color code...

Replacement tubing for the Rena XP Filters consists of two, 5 foot lengths. These are the original tubes that come with the XP1, XP2 & XP3. They will also fit the XP4....

This is the seal on the bottom of the motor that prevents water from the aquarium bypassing the filter material. It is a strip of sealing material that fits in the gro...

The item 851500-02 version of the canister replacement for the Rena Filstar XP2 external canister filter consists of the outer canister, rubber feet and clips. To avoi...

Original replacement motor for the Rena Filstar XP2 and includes a canister Oring and impeller cover seal . It does not include the Quick Disconnect Unit or rotor/impe...

The item 861500-02 version of the canister replacement for the Rena Filstar XP3 external canister filter consists of the outer canister, rubber feet and clips. To avoi...

Original replacement motor for the Rena Filstar XP3 and includes a canister Oring and impeller cover seal. It does not include the Quick Disconnect Unit, rotor/impelle...

The item 871500-00 version of the canister replacement for the Rena Filstar XP4 external canister filter consists of the outer canister, rubber feet and clips. To avoi...

Original replacement motor for the Rena Filstar XP4. Includes a canister Oring and impeller cover seal. It does not include the Quick Disconnect Unit, impeller cover o...

The inlet pipe cap covers the priming tube that is part of the inlet pipe. A loose inlet cap can let air into the intake system which makes priming and restarting the ...

Replacement suction cups for all XP Filter systems made after 2003. Includes suction cups only. No Clips.

These one-way locking clamps will secure the flexible tubing to both the inlet and outlet pipe at one end and the canister tubing barbs on the Quick Disconnect unit on...

Medium suction cups are used with all Rena Heaters, Micro-Bubblers and version 1 of the Rena Filstar XP canister filters inlet/outlet accessory packs.

Additional SmartFilter inlet extensions can be used to increase the intake length for use in deeper tanks.

Additional SmartFilter inlet extensions can be used to increase the intake length for use in deeper tanks. Old Item #841562-00

The inlet strainer attaches to the inlet extension and prevents gravel and other debris from clogging the filter. It is recommended to mount the strainer no closer tha...

This is the original factory replacement of the rotor/impeller assembly for the Rena Filstar XP1 and includes a new shaft and bearing/bushing. The rotor is the magnet ...

These are the original suction cups and clips (KeyCodes K&L)that come packed in the trays with new XP filters. Now packed in a convenient 6 pack (6 cups, 6 clips).

This is the original factory replacement of the rotor/impeller assembly for the Rena Filstar XP2 and includes a new shaft and bearing/bushing. The rotor is the magnet ...

This is the original factory replacement of the rotor/impeller assembly for the Rena Filstar XP3 and includes a new shaft and bearing/bushing. The rotor is the magnet ...

This is the original factory replacement of the rotor/impeller assembly for the Rena Filstar XP4 and includes a new shaft and bearing/bushing. The rotor is the magnet ...

This is the original factory replacement of the rotor/impeller assembly for the Aquael Unimax 500 and 700. It does not include the shaft and rubber bearing. The rotor ...

Our range of clear vinyl tubing is ideal for fountain, aquarium or pond use. The high content of virgin vinyl makes this tubing soft and pliable yet kink resistant and...

Replacement motor with new UV LEDS. Replace when motor stops working or LEDS begin to fade. Does not include a new rotor/impeller.

This is original multi-language manual included with all Filstar XP filters. These manuals are not specific to each model but the instructions for setup are the same f...